求助，Cube生成的fsmc代码为何没有IO初始化代码？难道不需...

Mr.rong

表示：？？/、/、/、、、、/

Mr.rong

free-368046

我生成的有IO初始化啊
void MX_FSMC_Init(void)
{
  FSMC_NORSRAM_TimingTypeDef Timing;

  /** Perform the SRAM1 memory initialization sequence
  */
  hsram1.Instance = FSMC_NORSRAM_DEVICE;
  hsram1.Extended = FSMC_NORSRAM_EXTENDED_DEVICE;
  /* hsram1.Init */
  hsram1.Init.NSBank = FSMC_NORSRAM_BANK1;
  hsram1.Init.DataAddressMux = FSMC_DATA_ADDRESS_MUX_ENABLE;
  hsram1.Init.MemoryType = FSMC_MEMORY_TYPE_PSRAM;
  hsram1.Init.MemoryDataWidth = FSMC_NORSRAM_MEM_BUS_WIDTH_8;
  hsram1.Init.BurstAccessMode = FSMC_BURST_ACCESS_MODE_DISABLE;
  hsram1.Init.WaitSignalPolarity = FSMC_WAIT_SIGNAL_POLARITY_LOW;
  hsram1.Init.WrapMode = FSMC_WRAP_MODE_DISABLE;
  hsram1.Init.WaitSignalActive = FSMC_WAIT_TIMING_BEFORE_WS;
  hsram1.Init.WriteOperation = FSMC_WRITE_OPERATION_ENABLE;
  hsram1.Init.WaitSignal = FSMC_WAIT_SIGNAL_DISABLE;
  hsram1.Init.ExtendedMode = FSMC_EXTENDED_MODE_DISABLE;
  hsram1.Init.AsynchronousWait = FSMC_ASYNCHRONOUS_WAIT_ENABLE;
  hsram1.Init.WriteBurst = FSMC_WRITE_BURST_DISABLE;
  /* Timing */
  Timing.AddressSetupTime = 1;
  Timing.AddressHoldTime = 1;
  Timing.DataSetupTime = 5;
  Timing.BusTurnAroundDuration = 0;
  Timing.CLKDivision = 16;
  Timing.DataLatency = 17;
  Timing.AccessMode = FSMC_ACCESS_MODE_A;
  /* ExtTiming */

  if (HAL_SRAM_Init(&hsram1, &Timing, NULL) != HAL_OK)
  {
    Error_Handler();
  }

}

static uint32_t FSMC_Initialized = 0;

static void HAL_FSMC_MspInit(void){
  /* USER CODE BEGIN FSMC_MspInit 0 */

  /* USER CODE END FSMC_MspInit 0 */
  GPIO_InitTypeDef GPIO_InitStruct;
  if (FSMC_Initialized) {
    return;
  }
  FSMC_Initialized = 1;
  /* Peripheral clock enable */
  __HAL_RCC_FSMC_CLK_ENABLE();
  
  /** FSMC GPIO Configuration  
  PE7   ------> FSMC_DA4
  PE8   ------> FSMC_DA5
  PE9   ------> FSMC_DA6
  PE10   ------> FSMC_DA7
  PD14   ------> FSMC_DA0
  PD15   ------> FSMC_DA1
  PD0   ------> FSMC_DA2
  PD1   ------> FSMC_DA3
  PD4   ------> FSMC_NOE
  PD5   ------> FSMC_NWE
  PD6   ------> FSMC_NWAIT
  PD7   ------> FSMC_NE1
  PB7   ------> FSMC_NL
  */
  /* GPIO_InitStruct */
  GPIO_InitStruct.Pin = GPIO_PIN_7|GPIO_PIN_8|GPIO_PIN_9|GPIO_PIN_10;
  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;

  HAL_GPIO_Init(GPIOE, &GPIO_InitStruct);

  /* GPIO_InitStruct */
  GPIO_InitStruct.Pin = GPIO_PIN_14|GPIO_PIN_15|GPIO_PIN_0|GPIO_PIN_1
                          |GPIO_PIN_4|GPIO_PIN_5|GPIO_PIN_7;
  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;

  HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);

  /* GPIO_InitStruct */
  GPIO_InitStruct.Pin = GPIO_PIN_6;
  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
  GPIO_InitStruct.Pull = GPIO_NOPULL;

  HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);

  /* GPIO_InitStruct */
  GPIO_InitStruct.Pin = GPIO_PIN_7;
  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;

  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

  /* USER CODE BEGIN FSMC_MspInit 1 */

  /* USER CODE END FSMC_MspInit 1 */
}

void HAL_SRAM_MspInit(SRAM_HandleTypeDef* sramHandle){
  /* USER CODE BEGIN SRAM_MspInit 0 */

  /* USER CODE END SRAM_MspInit 0 */
  HAL_FSMC_MspInit();
  /* USER CODE BEGIN SRAM_MspInit 1 */

  /* USER CODE END SRAM_MspInit 1 */
}

static uint32_t FSMC_DeInitialized = 0;

static void HAL_FSMC_MspDeInit(void){
  /* USER CODE BEGIN FSMC_MspDeInit 0 */

  /* USER CODE END FSMC_MspDeInit 0 */
  if (FSMC_DeInitialized) {
    return;
  }
  FSMC_DeInitialized = 1;
  /* Peripheral clock enable */
  __HAL_RCC_FSMC_CLK_DISABLE();
  
  /** FSMC GPIO Configuration  
  PE7   ------> FSMC_DA4
  PE8   ------> FSMC_DA5
  PE9   ------> FSMC_DA6
  PE10   ------> FSMC_DA7
  PD14   ------> FSMC_DA0
  PD15   ------> FSMC_DA1
  PD0   ------> FSMC_DA2
  PD1   ------> FSMC_DA3
  PD4   ------> FSMC_NOE
  PD5   ------> FSMC_NWE
  PD6   ------> FSMC_NWAIT
  PD7   ------> FSMC_NE1
  PB7   ------> FSMC_NL
  */

  HAL_GPIO_DeInit(GPIOE, GPIO_PIN_7|GPIO_PIN_8|GPIO_PIN_9|GPIO_PIN_10);

  HAL_GPIO_DeInit(GPIOD, GPIO_PIN_14|GPIO_PIN_15|GPIO_PIN_0|GPIO_PIN_1
                          |GPIO_PIN_4|GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7);

  HAL_GPIO_DeInit(GPIOB, GPIO_PIN_7);

  /* USER CODE BEGIN FSMC_MspDeInit 1 */

  /* USER CODE END FSMC_MspDeInit 1 */
}

void HAL_SRAM_MspDeInit(SRAM_HandleTypeDef* sramHandle){
  /* USER CODE BEGIN SRAM_MspDeInit 0 */

  /* USER CODE END SRAM_MspDeInit 0 */
  HAL_FSMC_MspDeInit();
  /* USER CODE BEGIN SRAM_MspDeInit 1 */

  /* USER CODE END SRAM_MspDeInit 1 */
}
/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

zhao.zhao

总结一下，CUBE中，底层和引脚有关的初始化都是在 HAL_XXX_MspInit() 中完成的

枫天2015

越看越迷糊。。。。谁有cub的fsmc的例程

themql

wofei1314 发表于 2015-10-23 15:27
再请教一下，是不是直接用我面贴的代码就无需初始化GPIO了？
刚才搜了一下你说的那个函数，确实找到了初 ...

楼主，我还是没发现HAL_SRAM_Init（）被谁调用了，
能麻烦讲解下吗